感悟人生

君生我未生,我生君已老
君恨我生迟,我恨君生早
君生我未生,我生君已老
恨不生同时,日日与君好
我生君未生,君生我已老
我离君天涯,君隔我海角
我生君未生,君生我已老
化蝶去寻花,夜夜栖芳草

迎各位朋友登陆我的网页,提供的资料希望对你有所帮助,希望相互交流,共同提高。有不到之处,还望各位朋友谅解。注:有些资料经过多次转载,作者已无从查找,如有侵权,请Email告知,本人会在第一时间内消除影响。



[技术资料] STAR机械手故障
感悟人生之工作第一 发表于:2008/4/19 23:30:21
标签(TAG):STAR机械手故障
The mold does not  1) Is the vertical cylinder descending? 1) Press the Up key to raise the vertical  
     close 2) Does the productconfirmation     cylinder
      limit switch come on after the  2) Adjust the limit switch and check the wiring
模具不关闭     product is chunked automatically? 3) Check the ON conditions and the interlock
  3) Is the mold close safety signal  4) Check the ON conditions to see if they are  
     comes on?     correct.
  4) Is the cycle start display ON?  
    1)  使用操作面板的上来上升机械手
  1) 机械手是否竖直下降 2) 检查限位开关及相关连线
  2) 产品被夹住后产品确认限位开关是否 3) 检查ON的条件和互锁
     自动转ON  4) 检查ON的条件是否满足
  3) 模具关闭安全信号是否转ON?   http://www.eyflu.com.cn//dispbbs.asp?boardID=8&ID=803&page=1
  4) 周期开始的显示是否为ON?  
The Mold does not 1) Is the vertical cylinder descending? 1) Press the Up key to raise the vertical cylinder  
open 2) Is the mold open safety signal  2) Check the On conditions and the interlock
模具不开    comes on?  
    1) 使用操作面板的上来上升机械手
  1) 机械手是否竖直下降? 2) 检查ON的条件是否满足
  2) 模具关闭安全信号是否转ON?  
No descent movement 1) Is the mold open conplete (MO) 1) Adjust the limit switch on the molding
无下降动作    signal comes on?(extracting-side)     machine and check the wiring of the  
  2) Are the swing action-end and swing     control box.
     return-end limit switches(on the  2) Adjust the limit switch on the molding machine  
     extracting and release side) function     and check the wiring.  
     correctly? 3) Loosen gradually until descent movement starts.
  3) Is the desent speed control valve shut 4) Replace bad valve.
     too tightly? 5) See the section"Manual Operations"  and
  4) Is the solenoid valve bad?    "Automatic Operations"
  5) Have the input condifions been met? 6) Replace bent hoss.
  6) Is the air hose bent? 7) Replace the packing.
  7) Is the packing inside the cylinder  
     damaged? 1) 调整注塑机的限位开关并检查到控制盒的连线
    2) 调整注塑机的限位开关并检查相关连线
  1) 模开完成信号(MO)是否为ON 3) 逐渐松动阀门直到机械手开始下降
  2) 机械手摆动复归和摆动到位的限位开 4) 更换损坏的阀门
      关是否工作正常? 5) 参看有关“手动操作“和“自动操作”
  3) 机械手下降速度控制气阀是否锁得太 6)更换损坏的气管  
     紧? 7) 更换密封
  4) 电磁阀是否损坏?  
  5) 是否满足输入条件?  
  6) 气管是否被弯曲?  
  7) 气缸内部密封是否损坏?  
No advance 1) Have the input conditions been met? 1) See the section "Manual Operations" and  
movement 2) Is the advance speed control valve shut    "Automatic Operations"
      too tightly? 2) Loosen gradually until advance movement
无前进动作 3) Is the solenoid valve bad?    start
  4) Is the air hose bent? 3) Replace bad valve
  5) Is the packing inside the cylinder damaged? 4) Replace bent hose.
    5) Replace the packing
  1) 输入条件是否满足?  
  2) 前进的速度控制阀门是否关得太*? 1)  参看“手动操作”和“自动操作”
  3) 电磁阀门是否损坏? 2) 逐渐松动阀门直到机械手开始前进
  4) 气管是否被弯曲? 3) 更换损坏的阀门
  5) 气缸内部密封是否损坏?   4) 更换气管
    5) 更换密封
The Product is not  1) Are the input conditions met? 1) See the section "Manual Operations" and  
gripped 2) The chuck cylinder is defective?     "Automatic Operations"
  3) The solenoid valve is defective? 2) Replace the chuck cylinder
产品未抓紧 4) Is the molding machine mold open stroke correct? 3) Replace the solenoid valve
  5) Is the uploader crosswise stroke correct? 4) Adjust the molding open of molding machine.
  6) Is the protrusion of ejector pin appropriate?Is the  5) Adjust the crosswise stroke.
     setting time on the timer appropriate? 6) Adjust the ejector advance stroke on the molding  
  7) The hose for the chuck pipe is loose.     machine side
  8)  Has mold separation deteriorated? 7) If the hose is loose, replace it with now one.
    8) Apply mold separation solution or repair the metal
  1) 输入条件是否满足?     mold.
  2) 产品夹的气筒是否损坏?  
  3) 电磁阀是否损坏? 1)  参看“手动操作”和“自动操作”
  4) 注塑机的模开行程是否正确? 2) 更换夹子的气筒
  5) 机械手的摆动行程是否正确? 3) 更换电磁阀
  6) 顶针的顶出是否合适?定时器的时间设定是否合适? 4) 调整注塑机的开模
  7) 夹子的气管是否松? 5)  调整摆动行程
  8) 开模情况是否恶化 6)  调整注塑机的顶针顶出行程
   7)  如果气管松,更换新的
   8)  修理模具
No return  1) Have the input conditions been met? 1) See the section "Manual Operation"...  
movement 2) Are the swing action-end and swing return-end limit 2) Adjust the limit switch on the molding machine  
      switches(on the extracting and release side)        and check the wiring.  
无回位     function correctlly? 3) Replace bad valve
  3) Is the solenoid valve bad?  
    1)  参看“手动操作”和“自动操作”
  1) 输入条件是否满足? 2) 调整注塑机的限位开关并检查相关连线
  2) 机械手摆动复归和摆动到位的限位开关是否正常? 3) 更换坏的电磁阀
  3) 电磁阀是否损坏?  
No ascent 1) Have the input conditions been met? 1) See the section "Manual Operation"...  
  2) Is the ascent speed control valve shut too tightly? 2) Loosen gradually until ascent movement
无上升 3) Is the solenoid valve bad?     starts
    3) Replace bad valve
  1) 输入条件是否满足?  
  2) 上升速度控制阀门是否关得太警? 1)  参看“手动操作”和“自动操作”
  3) 电磁阀是否损坏? 2) 逐渐松动阀门直到机械手开始上升
    3) 更换坏的电磁阀
No swing 1) Are swing-action and swing-return signal being  1) Refer to section "Manual Operation"...  
     output? 2) Loosen gradually until swing starts
无摆动  2) Is swing speed control valve shut too tightly? 3) Replace bad valve
  3) Is solenoid valve bad? 4) Replace bent hose.
  4) Is the air hose bent? 5) Replace bad packing.
  5) Is cylinder packing bad?  
    1) Refer to section "Manual Operation"...  
  1) 摆动复归及摆动到位? 2) 逐渐松动阀门直到机械手开始摆动
  2) 摆动的速度控制阀门是否关得太紧? 3) 更换坏的阀门
  3) 电磁阀是否损坏? 4) 更换气管
  4) 气管是否弯曲? 5) 更换密封
  5) 气筒内密封是否损坏?  
Swing stops midway 1) Does Product-Confirmation signal go OFF during 1) Check limit-switch setting and wiring.
      swing? 2) Check  limit-switch setting and wiring.
机械手摆动中途停止 2) Are ascent-end and return-end switches OFF?  
    1) 检查限位开关和相关连线
  1) 机械手摆动过程中产品确认信号是否变OFF 2) 检查限位开关及相关连线
  2) 上升结束和回位开关是否变OFF?  

阅读(5847) 评论(0)



回复:STAR机械手故障
(匿名游客) 发表于:2017/3/25 16:24:14

我们的STAR机械手这几天老是突然断电,有的时候是连续断电,有的时候一两天也不会发生这样的问题,请问大神是什么情况?能否帮助,这是我的微信13644072661李


引用 | 举报回复



回复:STAR机械手故障
(匿名游客) 发表于:2014/9/17 19:10:16

STAR机械手不小心被初始化了、现在机械手行走往反方向走了、怎么解决啊


引用 | 举报回复



回复:STAR机械手故障
(匿名游客) 发表于:2014/4/19 14:07:17

机械手无自动循环,
引用 | 举报回复



回复:STAR机械手故障
13148801889(游客) 发表于:2010/7/11 8:15:06

楼主是做维修的吗,我也专修STAR电控哦
引用 | 举报回复



回复:STAR机械手故障
lq200245 发表于:2008/5/6 21:24:06

还可以啊


引用 | 举报回复




 
  日历 


  登录 


  我的分类  


  最新日志 


  最新评论  
 

  Blog统计 
 

博客名称:感悟人生 日志总数:37 评论数量:37 访问次数:102934 建立时间::2008年04月19日

  友情链接 


  给我留言


  搜索 

      XML RSS 2.0
 

中华工控网 | 联系我们 | 工控论坛首页 | 首页 | 博客注册 | 博客登陆

工控博客管理联系邮箱:工控博客服务邮箱

中华工控网 © Copyright 2013. All rights reserved.